CR5211-50,CR5211-50 pdf中文资料,CR5211-50引脚图,CR5211-50电路-Datasheet-电子工程世界

文档预览

DC Current Transducer

DIN RAIL / PANEL MOUNT, RMS

The

CR5200

Series, DC Current Transducers are designed to

provide a DC signal which is proportional to a DC sensed

current. These devices are designed for direct current only,

targeting them towards general and daily applications. The

ranges 2 to 10 Amp utilize an advanced Magnetic Modulator

technology and the ranges 20 amps and above utilize Hall

Effect technology.

Applications

Battery chargers and systems

DC motor drives

Power supply management

Mobile applications

CR5210

CR5211

CR5220

Transducers

Single Element - .79” Window

0.1 to 600 ADC Input Range

Features

Closed loop sensing for accuracy

35mm DIN rail or panel mount

Available with ±5 VDC, ±10 VDC or 4 - 20 mADC outputs

Non-contact DC current sensing

Connection diagram printed on case

Regulatory Agencies

Constructed to meet UL 61010B-1

Constructed to meet CAN/CSA-C22.2, No. 61010-1-2004

Meets requirement of IEC 61010-1 and BS EN 61010-1

CR5210S

CR5211S

CR5220S

Single Element - 1.2” Window

20 to 600 ADC Input Range

E199795

Contact Factory for Custom

±5 VDC, ±10 VDC

or 4 - 20 mADC

Output Options

All single phase current transducers are available in split

core design. Simply put an “S” at the end of the prefix*

I.E. CR5210S-30

Add suffix for input range

PART NUMBERS

CR5210(S)

CR5211(S)

CR5220(S)

Single Element with ± 5 VDC output (split core design)

Single Element with ± 10 VDC output (split core design)

Single Element with 4 - 20 mADC output (split core design)

NOTE: DC Split Core Transducers Available in 20 Amps and Higher

NOTE:

CR5200 Series is available with 12V Power Supply. Use same application as 24V Power Supply.

Example Part Number: CR5210-300-12V

100

150

300

0-2 ADC

0-5 ADC

0-10 ADC

0-20 ADC

0-30 ADC

0-50 ADC

0-75 ADC

0-100 ADC

0-150 ADC

0-300 ADC

Ranges available up to and

including 600 ADC

The Professional

Energy Monitoring

Company

ISO 9001:2008 Quality Management System

M N TI

3500 Scarlet Oak Blvd. St. Louis MO USA 63122 V: 636-343-8518 F: 636-343-5119

Web: http://www.crmagnetics.com

E-mail: sales@crmagnetics.com

DC Current Transducer

DIN RAIL / PANEL MOUNT, RMS

SPECIFICATIONS

Basic Accuracy:........................ 1.0 %

Linearity:................................... 10% to 100% FS

Thermal Drift:............................ 500 PPM/°C

Operating Temperature:............ 0°C to +50°C

Installation Category:................ CAT II

Isolation Voltage:.......................

3500KVRMS/1mA/1Sec

Vibration Tested To:................... IEC 60068-2-6,1995

Pollution Degree:..................... 2

Response Time: ..................... 250 ms

Altitude:................................... 2000 meter max.

Insulation Voltage:................... 2500 VDC

Supply Voltage:....................... 24 VDC ±10%

Frequency Range:.................. DC Only

Cleaning:................................ Water-dampened cloth

MTBF:......................... Greater than 100 K hours

Output Load:............... 4-20 mADC - 0 to 300

0-5 VDC - 2K

or Greater

Relative Humidity:..... 5% to 95%, Non-Condensing

Supply Current:

CR5210:.................... Typical 35mA

Max 40mA

CR5210S:.................. Typical 30mA

Max 35mA

CR5220:.................... Typical 60mA

Max 100mA

CR5220S:.................. Typical 40mA

Max 50mA

Torque Specs.:........... 3.0 inch lbs. (0.4Nm)

Weight:....................... 0.5 lbs.

Transducers

[26.6]

1.05

OUTPUT

SUPPLY

[3.3]

.13

Optional

Mounting

[73.1]

2.88

[83.3]

3.28

DIN RAIL

MOUNTING

CLIP

[41.8]

1.65

[20.1]

.79

CR5210

CR5211

[76.6]

3.02

5 VDC Output

10 VDC Output

[5.6]

.22

TYP

[88.7]

3.49

[25]

.98

[50.7]

2.00

OUTPUT

SUPPLY

CR5220

4 - 20 mADC Output

[28.3]

1.12

[36.6]

1.44

OUTLINE DRAWING

CONNECTION DIAGRAM

NOTE: The building installation must have a switch or circuit-breaker that is in close proximity and within easy reach of the operator. The switch or circuit

breaker shall be marked as the disconnecting device for the equipment.